Get 100% Authentic Fortinet NSE6_FWF-6.4 Dumps with Correct Answers
New Training Course NSE6_FWF-6.4 Tutorial Preparation Guide
NEW QUESTION # 22
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)
- A. DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.
- B. DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.
- C. DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
- D. DARRP measurements can be scheduled to occur at specific times.
Answer: A,D
Explanation:
According to Fortinet training: "When using DARRP, the AP selects the best channel available to use based on the scan results of BSSID/receive signal strength (RSSI) to AC" and "To set the running time for DARRP optimization, use the following CLI command within the wireless controller setting: set darrp-optimize {integer}. Note that DARRP doesn't do continuous spectrum analysis..."
NEW QUESTION # 23
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)
- A. DARRP measurements can be scheduled to occur at specific times.
- B. DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.
- C. DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
- D. DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.
Answer: B,C
Explanation:
DARRP (Distributed Automatic Radio Resource Provisioning) technology ensures the wireless infrastructure is always optimized to deliver maximum performance. Fortinet APs enabled with this advanced feature continuously monitor the RF environment for interference, noise and signals from neighboring APs, enabling the FortiGate WLAN Controller to determine the optimal RF power levels for each AP on the network. When a new AP is provisioned, DARRP also ensures that it chooses the optimal channel, without administrator intervention.
NEW QUESTION # 24
Refer to the exhibit.
What does the asterisk (*) symbol beside the channel mean?
- A. Indicates channels that can be used only when Radio Resource Provisioning is enabled
- B. Indicates channels that will be scanned by the Wireless Intrusion Detection System (WIDS)
- C. Indicates channels that are subject to dynamic frequency selection (DFS) regulations
- D. Indicates channels that cannot be used because of regulatory channel restrictions
Answer: A
NEW QUESTION # 25
Which statement describes FortiPresence location map functionality?
- A. Provides real-time insight into user online activity
- B. Provides real-time insight into user usage stats
- C. Provides real-time insight into user purchase activity
- D. Provides real-time insight into user movements
Answer: B
Explanation:
This geographical data analysis provides real-time insights into user behavior.
NEW QUESTION # 26
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit C
A wireless network has been installed in a small office building and is being used by a business to connect its wireless clients. The network is used for multiple purposes, including corporate access, guest access, and connecting point-of-sale and IoT devices.
Users connecting to the guest network located in the reception area are reporting slow performance. The network administrator is reviewing the information shown in the exhibits as part of the ongoing investigation of the problem. They show the profile used for the AP and the controller RF analysis output together with a screenshot of the GUI showing a summary of the AP and its neighboring APs.
To improve performance for the users connecting to the guest network in this area, which configuration change is most likely to improve performance?
- A. Increase the transmission power of the AP radios
- B. Install another AP in the reception area to improve available bandwidth
- C. Reduce the number of wireless networks being broadcast by the AP
- D. Enable frequency handoff on the AP to band steer clients
Answer: D
NEW QUESTION # 27
How can you find upstream and downstream link rates of a wireless client using FortiGate?
- A. On the FortiGate GUI, using the WiFi Client monitor
- B. On the FortiGate CLI, using the diag wireless-controller wlac -d Sta command
- C. On the FortiAP CLI, using the cw_diag ksta command
- D. On the FortiAP CLI, using the cw_diag -d sta command
Answer: A
Explanation:
Explanation
The WiFi Client monitor on the FortiGate GUI shows the upstream and downstream link rates of a wireless client, along with other information such as MAC address, SSID, IP address, signal strength, and connection time. The link rates indicate the maximum data rates that the client can achieve in both directions.
References: Secure Wireless LAN Course Description, page 7; [FortiOS 6.4.0 Handbook - Wireless Controller], page 37.
NEW QUESTION # 28
A tunnel mode wireless network is configured on a FortiGate wireless controller.
Which task must be completed before the wireless network can be used?
- A. The wireless network to Internet firewall policy must be configured
- B. The wireless network interface must be assigned a Layer 3 address
- C. The new network must be manually assigned to a FortiAP profile.
- D. Security Fabric and HTTPS must be enabled on the wireless network interface
Answer: A
Explanation:
A FortiGate unit is an industry leading enterprise firewall. In addition to consolidating all the functions of a network firewall, IPS, anti-malware, VPN, WAN optimization, Web filtering, and application control in a single platform, FortiGate also has an integrated Wi-Fi controller.
NEW QUESTION # 29
What is the first discovery method used by FortiAP to locate the FortiGate wireless controller in the default configuration?
- A. Multicast
- B. Broadcast
- C. DHCP
- D. Static
Answer: D
Explanation:
Explanation
According to the web search results, the first discovery method used by FortiAP to locate the FortiGate wireless controller in the default configuration is static. This means that the FortiAP sends discovery requests to a preconfigured IP address that the controller owns. This is useful if the FortiAP and the controller are not in the same subnet and other discovery methods will not work. The other discovery methods are used in sequence if the static method fails or is not configured. References: Advanced WiFi controller discovery | FortiAP / FortiWiFi 7.4.0
NEW QUESTION # 30
When enabling security fabric on the FortiGate interface to manage FortiAPs, which two types of communication channels are established between FortiGate and FortiAPs? (Choose two.)
- A. Control channels
- B. Data channels
- C. FortLink channels
- D. Security channels
Answer: A,B
Explanation:
The control channel for managing traffic, which is always encrypted by DTLS. l The data channel for carrying client data packets.
NEW QUESTION # 31
Refer to the exhibits.
Exhibit A
Exhibit B
A wireless network has been created to support a group of users in a specific area of a building. The wireless network is configured but users are unable to connect to it. The exhibits show the relevant controller configuration for the APs and the wireless network.
Which two configuration changes will resolve the issue? (Choose two.)
- A. Disable intra-vap-privacy for the Authors vap-wireless network
- B. For both interfaces in the wtp-profile, configure set vaps to be "Authors"
- C. Increase the transmission power of the AP radio interfaces
- D. For both interfaces in the wtp-profile, configure vap-all to be manual
Answer: B,D
NEW QUESTION # 32
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor
- B. Areas with the signal strength weaker than -68 dB are cut out of the map
- C. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.
- D. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility
Answer: A
NEW QUESTION # 33
When configuring Auto TX Power control on an AP radio, which two statements best describe how the radio responds? (Choose two.)
- A. When the AP detects any other wireless signal stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.
- B. When the AP detects PF Interference from an unknown source such as a cordless phone with a signal stronger that -70 dBm, it will increase its transmission power until it reaches the maximum configured TX power limit.
- C. When the AP detects any interference from a trusted neighboring AP stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.
- D. When the AP detects any wireless client signal weaker than -70 dBm, it will reduce its transmission power until it reaches the maximum configured TX power limit.
Answer: A,D
NEW QUESTION # 34
Which two phases are part of the process to plan a wireless design project? (Choose two.)
- A. Installation phase
- B. Hardware selection phase
- C. Site survey phase
- D. Project information phase
Answer: C,D
Explanation:
Explanation
According to the web search results, the project information phase and the site survey phase are part of the process to plan a wireless design project. The project information phase involves defining the project scope, objectives, requirements, deliverables, and stakeholders. It also includes creating a project plan, a risk management plan, a communication plan, and a budget.1 The site survey phase involves conducting a physical inspection of the site where the wireless network will be deployed, measuring the signal strength and interference levels, identifying the optimal locations for the access points and antennas, and validating the network performance and coverage.2 The hardware selection phase and the installation phase are not part of the planning process, but rather part of the implementation process. The hardware selection phase involves choosing the appropriate wireless devices, such as access points, routers, switches, controllers, and cables, based on the network design and specifications.3 The installation phase involves installing, configuring, testing, and documenting the wireless network components according to the project plan and best practices.3 References: Wireless Device Network Planning and Design - Emerson, Telecommunications and Implementation Project Management - BICSI, Project Planning | Wireless Design Services | Digi International
NEW QUESTION # 35
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor
- B. Areas with the signal strength weaker than -68 dB are cut out of the map
- C. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.
- D. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility
Answer: A
NEW QUESTION # 36
Refer to the exhibit.
What does the asterisk (*) symbol beside the channel mean?
- A. Indicates channels that will be scanned by the Wireless Intrusion Detection System (WIDS)
- B. Indicates channels that can be used only when Radio Resource Provisioning is enabled
- C. Indicates channels that are subject to dynamic frequency selection (DFS) regulations
- D. Indicates channels that cannot be used because of regulatory channel restrictions
Answer: C
Explanation:
Explanation
This frequencies are also used by other licensed applications, wireless LANs have to use a specific method to gain access to certain higher frequencies and this method is known as DFS.
NEW QUESTION # 37
Which of the following is a requirement to generate analytic reports using on-site FortiPresence deployment?
- A. SQL services must be running
- B. Two wireless APs must be sending data
- C. Wireless network security must be set to open
- D. DTLS encryption on wireless traffic must be turned off
Answer: A
NEW QUESTION # 38
As standard best practice, which configuration should be performed before configuring FortiAPs using a FortiGate wireless controller?
- A. Preauthorize APs
- B. Create wireless LAN specific policies
- C. Set the wireless controller country setting
- D. Create a custom AP profile
Answer: C
NEW QUESTION # 39
Which two roles does FortiPresence analytics assist in generating presence reports? (Choose two.)
- A. Reporting potential threats by guests on site
- B. Gathering details about on site visitors
- C. Comparing current data with historical records
- D. Predicting the number of guest users visiting on-site
Answer: B,C
NEW QUESTION # 40
Six APs are located in a remotely based branch office and are managed by a centrally hosted FortiGate.
Multiple wireless users frequently connect and roam between the APs in the remote office.
The network they connect to, is secured with WPA2-PSK. As currently configured, the WAN connection between the branch office and the centrally hosted FortiGate is unreliable.
Which configuration would enable the most reliable wireless connectivity for the remote clients?
- A. Configure a bridge mode wireless network and enable the Local standalone configuration option
- B. Install supported FortiAP and configure a bridge mode wireless network
- C. Configure a tunnel mode wireless network and enable split tunneling to the local network
- D. Configure a bridge mode wireless network and enable the Local authentication configuration option
Answer: A
Explanation:
Explanation
Look for "Continued FortiAP operation when WiFi controller connection is down" im the link here:
https://docs.fortinet.com/document/fortiap/7.0.4/fortiwifi-and-fortiap-configuration-guide/442078/how-to-config
NEW QUESTION # 41
When using FortiPresence as a captive portal, which two types of public authentication services can be used to access guest Wi-Fi? (Choose two.)
- A. Hardware security token authentication
- B. Software security token authentication
- C. Social networks authentication
- D. Short message service authentication
Answer: C,D
Explanation:
Explanation
According to the web search results, FortiPresence supports social networks authentication and short message service authentication as public authentication services for guest Wi-Fi access. Social networks authentication allows visitors to log in using their existing social media accounts, such as Facebook, Twitter, LinkedIn, Google, and Instagram. Short message service authentication allows visitors to receive a one-time password via SMS to their mobile phone number. These authentication methods are convenient and secure for visitors and provide valuable data for businesses. Software security token authentication and hardware security token authentication are not supported by FortiPresence as public authentication services for guest Wi-Fi access.
References: Configuring Captive Portal | FortiPresence 1.2.0, Configuring Captive Portal | FortiPresence
22.4.0
NEW QUESTION # 42
Refer to the exhibits.
Exhibit A
Exhibit B
The exhibits show the diagnose debug log of a station connection taken on the controller CLI.
Which security mode is used by the wireless connection?
- A. WPA2 Personal and radius MAC filtering
- B. Open, with radius MAC filtering
- C. WPA3 Enterprise
- D. WPA2 Enterprise
Answer: A
NEW QUESTION # 43
......
Dumps of NSE6_FWF-6.4 Cover all the requirements of the Real Exam: https://www.prep4away.com/Fortinet-certification/braindumps.NSE6_FWF-6.4.ete.file.html
Correct Practice Tests of NSE6_FWF-6.4 Dumps with Practice Exam: https://drive.google.com/open?id=17nJIb0UaG8YDxkr27yNxsI7P52yixr-g