Real Cisco 300-730 Exam Dumps with Correct 177 Questions and Answers
Valid 300-730 Test Answers & Cisco 300-730 Exam PDF
NEW QUESTION # 24
Which benefit of FlexVPN is a limitation of DMVPN using IKEv1?
- A. IKE implementation can install routes in routing table.
- B. Dynamic routing protocols can be configured.
- C. NHRP authentication provides enhanced security.
- D. GRE encapsulation allows for forwarding of non-IP traffic.
Answer: A
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_ike2vpn/configuration/15-mt/sec-flex-vpn-15-mt-book/sec-flex-spoke.html
NEW QUESTION # 25
Refer to the exhibit.
What is configured as a result of this command set?
- A. FlexVPN server to authorize groups by using an IPv6 external AAA
- B. FlexVPN server for an IPv6 dVTI session
- C. FlexVPN client profile for IPv6
- D. FlexVPN server to authenticate IPv6 peers by using EAP
Answer: B
Explanation:
https://www.cisco.com/c/en/us/support/docs/security/flexvpn/116528-config-flexvpn-00.html
NEW QUESTION # 26
Refer to the exhibit.
Which type of VPN implementation is displayed?
- A. IKEv1 cluster
- B. IKEv2 backup gateway
- C. IKEv2 load balancer
- D. IKEv2 reconnect
Answer: C
NEW QUESTION # 27
An engineer must configure remote desktop connectivity for offsite admins via clientless SSL VPN, configured on a Cisco ASA to Windows Vista workstations. Which two configurations provide the requested access? (Choose two.)
- A. SSH bookmark via the SSH plugin
- B. Citrix bookmark via the ICA plugin
- C. VNC bookmark via the VNC plugin
- D. RDP2 bookmark via the RDP2 plugin
- E. Telnet bookmark via the Telnet plugin
Answer: C,D
NEW QUESTION # 28
An engineer is implementing the FlexVPN solution on a Cisco IOS router. The router must only terminate VPN requests and must not initiate them. Additionally, the interface must support VPNs from other routers and Cisco AnyConnect connections. Which interface type must be configured to meet these requirements?
- A. virtual template interface
- B. static virtual tunnel interface
- C. multipoint GRE tunnel interface
- D. point-to-point GRE tunnel interface
Answer: A
Explanation:
The correct interface type to meet these requirements is the virtual template interface. This interface allows for the creation of multiple virtual access interfaces, which can be used for various types of remote access VPN connections, including site-to-site and AnyConnect VPNs. The virtual template interface can be configured to terminate VPN requests from other routers and allow for dynamic creation of VPN sessions, while also supporting AnyConnect VPN connections.
NEW QUESTION # 29
Which Cisco AnyConnect component ensures that devices in a specific internal subnet are only accessible using port 443?
- A. routing
- B. WebACL
- C. VPN filter
- D. split tunnel
Answer: C
Explanation:
https://www.cisco.com/c/en/us/support/docs/security/pix-500-series-security-appliances/99103-pix-asa-vpn-filter.html#anc6
NEW QUESTION # 30
What uses an Elliptic Curve key exchange algorithm?
- A. AES-GCM
- B. SHA
- C. ECDSA
- D. ECDHE
Answer: D
Explanation:
Section: Secure Communications Architectures
Explanation
Explanation/Reference: https://blog.cloudflare.com/a-relatively-easy-to-understand-primer-on-elliptic-curve-cryptography/
NEW QUESTION # 31
A network engineer must design a clientless VPN solution for a company. VPN users must be able to access several internal web servers. When reachability to those web servers was tested, it was found that one website is not being rewritten correctly by the ASA.
What is a potential solution for this issue while still allowing it to be a clientless VPN setup?
- A. Set up a smart tunnel with the IP address of the web server.
- B. Set up a WebACL to permit the IP address of the web server.
- C. Set up a NAT rule that translates the ASA public address to the web server private address on port 80.
- D. Set up Cisco AnyConnect with a split tunnel that has the IP address of the web server.
Answer: A
NEW QUESTION # 32
Which VPN technology must be used to ensure that routers are able to dynamically form connections with each other rather than sending traffic through a hub and be able to advertise routes without the use of a dynamic routing protocol?
- A. FlexVPN
- B. GETVPN
- C. DMVPN Phase 2
- D. DMVPN Phase 3
Answer: D
NEW QUESTION # 33
On a FlexVPN hub-and-spoke topology where spoke-to-spoke tunnels are not allowed, which command is needed for the hub to be able to terminate FlexVPN tunnels?
- A. interface virtual-access
- B. interface virtual-template
- C. ip nhrp redirect
- D. interface tunnel
Answer: B
Explanation:
On a FlexVPN hub-and-spoke topology where spoke-to-spoke tunnels are not allowed, the command that is needed for the hub to be able to terminate FlexVPN tunnels is interface virtual-template. The interface virtual-template command is used to configure a virtual template interface which provides a secure tunnel for FlexVPN connections. The other commands listed - interface virtual-access, ip nhrp redirect, and interface tunnel - are not related to FlexVPN and are not used to terminate FlexVPN tunnels.
NEW QUESTION # 34
Which two commands help determine why the NHRP registration process is not being completed even after the IPsec tunnel is up? (Choose two.)
- A. show crypto isakmp sa
- B. show dmvpn detail
- C. show crypto ipsec sa
- D. show ip nhrp traffic
- E. show ip traffic
Answer: A,D
NEW QUESTION # 35
Refer to the exhibit.
Which value must be configured in the User Group field when the Cisco AnyConnect Profile is created to connect to an ASA headend with IPsec as the primary protocol?
- A. group-alias
- B. group-policy
- C. address-pool
- D. tunnel-group
Answer: D
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/security/vpn_client/anyconnect/anyconnect41/ administration/guide/b_AnyConnect_Administrator_Guide_4-1/configure-vpn.html
NEW QUESTION # 36
What must be configured in a FlexVPN deployment to allow for direct communication between spokes connected to different hubs?
- A. Load balancing must be disabled.
- B. Hub routers must be on same Layer 2 network.
- C. EIGRP must be used as routing protocol.
- D. A GRE tunnel must exist between hub routers.
Answer: D
NEW QUESTION # 37
Refer to the exhibit.
Based on the exhibit, why are users unable to access CCNP Webserver bookmark?
- A. The ASA cannot resolve the URL.
- B. The bookmark has been disabled.
- C. The user cannot access the URL.
- D. The URL is being blocked by a WebACL.
Answer: B
NEW QUESTION # 38
Refer to the exhibit.
All internal clients behind the ASA are port address translated to the public outside interface that has an IP address of 3.3.3.3. Client 1 and client 2 have established successful SSL VPN connections to the ASA. What must be implemented so that "3.3.3.3" is returned from a browser search on the IP address?
- A. Tunnel Network List Below under Group Policy
- B. Exclude Network List Below under Group Policy
- C. Tunnel All Networks under Group Policy
- D. Same-security-traffic permit inter-interface under Group Policy
Answer: C
Explanation:
The reason is that by default, the SSL VPN clients use split tunneling, which means they only send traffic destined for the corporate network through the VPN tunnel, and use their local gateway for other traffic, such as browsing the internet. This means that when they search for their IP address on a browser, they will see their local IP address, not the IP address of the ASA.
To change this behavior, you need to configure the Group Policy on the ASA to tunnel all networks, which means that all traffic from the SSL VPN clients will go through the VPN tunnel, regardless of the destination. This way, when they search for their IP address on a browser, they will see the IP address of the ASA, which is 3.3.3.3.
To configure tunnel all networks under Group Policy, you can use either ASDM or CLI. For example, using ASDM, you can follow these steps1:
Choose Configuration > Remote Access VPN > Network (Client) Access > Group Policies.
Select the group policy that you want to modify and click Edit.
In the Edit Internal Group Policy window, choose Advanced > Split Tunneling.
In the Policy drop-down list, choose Tunnel All Networks.
Click OK and then Apply.
Using CLI, you can enter these commands:
ciscoasa(config)# group-policy <group_policy_name> attributes ciscoasa(config-group-policy)# split-tunnel-policy tunnelall
NEW QUESTION # 39
Which parameter in IPsec VPN tunnel configurations is optional?
- A. encryption
- B. hash
- C. lifetime
- D. Perfect Forward Secrecy
Answer: D
NEW QUESTION # 40
Which two parameters help to map a VPN session to a tunnel group without using the tunnel-group list? (Choose two.)
- A. group-alias
- B. optimal gateway selection
- C. AnyConnect client version
- D. group-url
- E. certificate map
Answer: D,E
NEW QUESTION # 41
......
300-730 Exam Questions and Valid PMP Dumps PDF: https://www.prep4away.com/Cisco-certification/braindumps.300-730.ete.file.html
Cisco 300-730 Certification Real 2023 Mock Exam: https://drive.google.com/open?id=1ZPyJEi0s8KIQNbZANiL8bKUUICcdzJYB